Oct 18, 2021
Version 2
PCR and gel electrophoresis V.2
- 1Indian Instituteof Science Education and Research, Pune
- iGEM IISER Pune India 2021
Protocol Citation: Ashwinuday 2021. PCR and gel electrophoresis . protocols.io https://dx.doi.org/10.17504/protocols.io.by6ppzdnVersion created by Ashwinuday
License: This is an open access protocol distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited
Protocol status: In development
We are still developing and optimizing this protocol
Created: October 18, 2021
Last Modified: October 18, 2021
Protocol Integer ID: 54191
Abstract
This protocol can be used to confirm genes or DNA of interest from a template using PCR. Also to amplify required amount of genes to larger amounts.
Safety warnings
EtBr and associated items and consumables during gel processing should be handles with gloves on and things which don't classify under items for gel should not be touched with gloved hands.
Prepare the working stock solution of all the reagents required. If already prepared and stored, takeout from the refrigerator and thaw on ice.
Prepare the following mixes each of total 50 µL : -
| A | B | C | |
| Items | negative control | test sample | |
| ultrapure water (from Milli-Q) | 40 ul | 39 ul | |
| pfu Buffer (10X) | 5 ul (1X) | 5 ul (1X) | |
| Forward primer (20uM) | 1 ul (0.4uM) | 1 ul (0.4uM) | |
| Reverse primer (20uM) | 1 ul (0.4uM) | 1 ul (0.4uM) | |
| dNTPs (2.5mM) | 2 ul (0.1mM) | 2 ul (0.1mM) | |
| Pfu polymerase | 1 ul | 1 ul | |
| Template (100ng/ul) | - | 1 ul (100ng) |
Perform PCR using a Thermo cycler with the following temperature settings (All temperatures are in degree Celcius) :
| A | B | |
| Temperature | Time | |
| 95 | 5 min | |
| 95 | 30 secs | |
| 55 | 40 secs | |
| 72 | 2 min | |
| 72 | 5 min |
Set the 2nd, 3rd and 4th steps to repeat 30 times (or maximum till 35)
Note
The PCR product can be immediately run analyzed using gel electrophoresis or can be stored in -20 °C or lower to be analyzed later.
Safety information
All items which interact with the gel and EtBr should be handled with gloves. Also ensure, the gloved hands are not used to touch anything other than gel materials.
To prepare the 1% agarose gel, mix 0.5 g of agarose in 50 mL of 1X TAE buffer and heat well to form a clear solution.
Note
Based on requirement higher amounts of gel can be prepared. So, accordingly larger combs and higher amount of EtBr can be used.
Then the mix is allowed to cool till it is bearable to touch. Carefully add 2 µL of EtBr to the mix and swirl well.
Then into a set gel cast with the appropriate comb (which is decided by the number of wells and the size of the wells required), pour the mix without bubbles.
Note
If there is any bubble remove it with a tip soon after pouring
Once the gel solidifies, carefully take it out with a gloved hand and place in the buffer tank with enough buffer to cover the immersed gel and remove the comb without breaking the wells.
Mix approximately 10 µL samples with 1X loading dye and load into each gel. Load a 1kb ladder (or any suitable ladder) into the first lane. Run the gel at 100V
After the dye front crosses 75%of the gel length, stop the current.
Take the gel out (with gloved hands) by letting all the buffer out into the tank and then image the gel on UV.
Compare the sample bands with the ladder to estimate the bands of interest